Turbosmart BLOW OFF & BYPASS VALVE KITS - Vee Port PRO fo Manuel d'utilisateur télécharger pdf

------------------------------------------------------------------------------------------------------------------------

IMPORTANT NOTES:

 Please thoroughly read and understand these instructions before commencing this installation.

 The thread on the cap for the vacuum source is AN#3. The standard swivel nipple can be changed to a AN#3 fitting if desired.

RECOMMENDATIONS

• Turbosmart recommends that your Blow off valve (BOV) is fitted and adjusted by an appropriately qualified technician

 Turbosmart recommends that a boost gauge be permanently fitted to the vehicle

------------------------------------------------------------------------------------------------------------------------

HOW TO INSTALL YOUR BOV

Please check that the following items have been provided in your Subaru Vee Port Pro kit.

Quantity

Description

Use

Subaru Vee Port Pro BOV

Model Specific blow off valve

34mm Blanking plug

To blank off the standard return pipe

Gasket

To seal the BOV to the intercooler pipe

1. Remove the standard BOV from the intercooler by removing the two bolts. Disconnect the vacuum line to the top of the standard

BOV.

2. Using pliers, carefully clamp onto the spring clamp on the plumb back hose and pull the BOV off the hose. Then carefully install the

provided 34mm blanking plug into the plumb back hose and secure it with the standard spring clamp.

3. Install the Vee Port Pro using the standard screws. Do not forget to install the provided gasket in between the BOV flange and the

intercooler flange. Re-fit the standard vacuum tube to the BOV.

4. Start the car and check for leaks.

ADJUSTING YOUR BOV

Each BOV needs to be adjusted to suit the vehicle it is being mounted on. The aim of the adjustment on Vee Port Pro, Supersonic and

Dual port is to make sure that the piston is hard closed at idle and that the piston closes fast enough to minimise backfiring and not stall

the engine. Plumb back BOV’s are equipped with a spring which are designed to keep the piston open at engine idle and hence the cap

can be left in the middle position.

Adjustment to the BOV is made by rotating the cap. To increase the spring force on the piston, rotate the cap clockwise in the direction

of hard as marked on the top of the cap. To decrease the spring force on the piston, rotate the cap anticlockwise in the direction of soft

as marked on the top of the cap - CAUTION - Do not rotate the cap beyond the first O-Ring indicator groove.

 Start with the BOV cap at the maximum soft position (The indicator O-Ring should be completely covered by the edge of the cap)

 With the engine at idle the exhaust port should be closed off by the piston – the piston should be hard against the seat and not

floating or moving

 Free rev the engine and back off quickly, the engine should return to normal idle speed – if the engine drops below idle or stalls

increase the spring tension by one turn

 Repeat this process until the engine free revs and returns to normal idle speed

 Test drive the car and ensure that when decelerating or changing gears that the engine has minimal backfiring and no stalling. If

backfiring is excessive or stalling is noticed then check all connections made during the installation, otherwise increase the spring

tension

Product Name: Subaru Vee Port Pro

Product Description: Fits WRX 01 – 07, WRX STI

01 – 08, Forester XT 06’

Product Number: TS-0205-1135, TS-0205-1136

Blanking plug

1 2 3

Résumé du contenu

Page 1 - HOW TO INSTALL YOUR BOV

1 ------------------------------------------------------------------------------------------------------------------------ IMPORTANT NOTES:  Pleas

Page 2 - TROUBLE SHOOTING

2 MAINTENANCE Turbosmart recommends that the following maintenance procedure is carried out at six monthly intervals or at higher intervals if the

Page 3 - Happy motoring!

3 ONE YEAR LIMITED WARRANTY Turbosmart is a company built on Customer Satisfaction and Service. That is why all of our products go through regi

Commentaires sur ces manuels

Pas de commentaire

Turbosmart BLOW OFF & BYPASS VALVE KITS - Vee Port PRO fo Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Turbosmart BLOW OFF & BYPASS VALVE KITS - Vee Port PRO fo. Turbosmart BLOW OFF & BYPASS VALVE KITS - Vee Port PRO for Subaru WRX (01-07), STI (01-08), Forester XT (06) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Turbosmart BLOW OFF & BYPASS VALVE KITS - Vee Port PRO fo